The Root 66 is a real advance in sectional cable machine design. No mid-range machine has its versatility and power. Look at its versatility. You can drive 5/8″ cables for lines up to 3″ and 7/8″ cables for 4″ lines – and you can switch from one to the other in seconds, without touching the jaws, without an adapter, without tools. And for sink drain work, slip on a drum that holds smaller cables. To operate, just feed a cable into the line and slide the back end into the machine. The excess cable goes into a guide tube. Turn on the sealed motor, press down on the handle, and the Root 66 starts spinning the cable at 400 rpm. The cable stops rotating as soon as you lift the handle, so there’s no additional torque buildup. When using a drum for small drain work, the drum stops turning when you lift the handle to the neutral position.
Cables:
“T” slot couplings slide together to lock and uncouple with a pin key.
5/8″ x 7-1/2 ft…for 1-1/4″ through 3″ lines up to 100 ft long;
7/8″ x 15 ft….for 2″ – 4″ lines up to 125 ft. long.
Stability and Durability:
The Root 66 has a wide four point base for greater stability. Its interlocking tubular construction also gives it excellent durability. To protect the gears from dirt and for easier cleaning, the machine has two internal plastic shields. A ground fault circuit interrupter is standard equipment.
Jaws:
Drive both 5/8″ and 7/8″ cables without adjustment; also grip containers for smaller diameter cables.
Leather Gloves:
With double-reinforced palm for hand protection when guiding cable.
Weight:
Weight: 42 lbs. (19 kg) without cable
Drip Guards:
Two shields to protect bearings and motor from dirt and moisture.
Clutch:
Pull down two position handle to spin cables at 400 RPM. Lift to stop. Brake stops spinning drums instantly.
Motor:
Sealed 1/2 hp with forward – off – reverse switch, ten foot power cord and ground fault circuit interrupter.
Dimensions:
16″ deep; 14″ wide; 17″ high. (40 cm x 35 cm x 43 cm).
Flexicore® Cable:
Heavy gauge wire is coiled around 49 strand wire rope and then heat treated. This cable has unequalled strength and the right amount of flexibility. It’s so tough, it has a one year warranty against defect or breakage. 3/4″ diameter for 4-10″ lines and 3″ lines without sharp bends. 5/8″ diameter for 3-6″ lines.
R-8CS Cutter set for 5/8″ cables:
Arrow Head, Boring Gimlet, 1-1/2″ U-Cutter and Retrieving Tool.
R-10CS Cutter set for 7/8″ cables:
Spear Head, 2″ U-Cutter, 3″ U-Cutter, Hook Auger and Retrieving Tool.
| PART # | Cable(s) | Weight | Price |
|---|---|---|---|
| RT-66 | Basic Unit: 1/2 hp Motor w/Rev. Switch,10 ft. Power Cord w/GFI, Leather Gloves | 47 lbs. | $2305.00 |
| RT-66-A | Basic Unit + six 7.5R8 Sections, SCC Cable Carrier, Rear Guide Hose, R-8CS Cutter Set | 72 lbs. | $2789.00 |
| RT-66-C | Basic Unit + five 15R10 Sections, CC Cable Carrier, Rear Guide Hose, R-10CS Cutter Set, Tool Box. | 122 lbs. | $3086.00 |
| RT-66-D | Basic Unit + Hardware from Units A and C. | 143 lbs. | $3497.00 |
| RT-66-E | Same as RT-66-D,plus small drum with 25 ft. x 5/16" cable. | 153 lbs. | $3877.00 |
*R-8CS Cutter Set (for 5/8″ cables): Arrow Head, Boring Gimlet, 1-1/2″ U-Cutter and Retrieving Tool.
R-10CS Cutter Set (for 7/8″ cables): Spear Head, 2″ U-Cutter, 3″ U-Cutter, Hook Auger and Retrieving Tool.
Reviews
There are no reviews yet.